芜湖 DS3800HMPK1J1H GE微处理器板 设计用于快速安装在驱动器中

芜湖 DS3800HMPK1J1H GE微处理器板 设计用于快速安装在驱动器中

产品描述

GE微处理器板DS3800HMPK1J1H设计用于快速安装在驱动器中。该板的一端有一个模块化连接器，另一端有一个固定杆。GE微处理器板DS1HMPK3800J1H还装有1个红色指示灯LED和3个琥珀色LED，从板的前面可见。该板还配备了微处理器、可擦除可编程只读存储器 （EPROM） 模块和 1 引脚连接器。它还装有 34 个 2 针连接器。

驱动器操作员可以在驱动器运行时查看 GE 微处理器板上的指示灯 DS3800HMPK1J1H。当电路板中存在全电压并且电路板已成功通过启动诊断测试时，琥珀色 LED 亮起。当琥珀色 LED 不亮时，有几个可能的原因。这可能是因为主板未通过启动诊断测试，或者电源不存在。第一个故障排除步骤是重新拔插主板机架中的主板。

断开驱动器的所有电源。请注意，驱动器具有 1 个以上的电源，在触摸驱动器中的任何组件之前，必须断开所有电源。断开断路器的电源以断开交流电源。从整流器上取下保险丝以断开直流电源。提起固定拉杆以卸下主板。然后，重置主板并用拇指小心地将电路板固定在模块化连接器中。合上固定拉杆并重新启动驱动器，以验证主板是否正常工作以及琥珀色指示灯是否亮起。

芜湖 DS3800HMPK1J1H GE微处理器板 设计用于快速安装在驱动器中

Product description

The GE microprocessor board DS3800HMPK1J1H is designed for quick installation in a drive. The board has a modular connector at one end and a fixed rod at the other end. The GE microprocessor board DS1HMPK3800J1H also has one red indicator LED and three amber leds visible from the front of the board. The board is also equipped with a microprocessor, erasable programmable read-only memory (EPROM) module, and a 1-pin connector. It also has 34 2-pin connectors.

The driver operator can view the indicator DS3800HMPK1J1H on the GE microprocessor board while the driver is running. When full voltage is present in the board and the board has successfully passed the start-up diagnostic test, the amber LED lights up. When amber leds don't light up, there are several possible reasons. This may be because the motherboard fails the startup diagnostic test, or the power supply is not present. The first troubleshooting step is to re-insert the motherboard in the motherboard rack.

Disconnect all power from the drive. Note that the drive has more than 1 power supply and all must be disconnected before touching any component in the drive. Disconnect the power from the circuit breaker to disconnect the AC power supply. Remove the fuse from the rectifier to disconnect the DC power supply. Lift the retaining tie rod to remove the motherboard. Then, reset the motherboard and carefully secure the board in the modular connector with your thumb. Close the retaining rod and restart the drive to verify that the motherboard is working properly and that the amber indicator light is on.